The use of silicon carbide (SiC) as a base material in power electronics has manyadvantages, including high breakdown voltage and excellent temperature endurance.However, the packaging of such electronics presents major challenges and there is aneed for packaging that can operate in higher temperature. The purpose of this thesishas been to develop a test method and verify the functionality of SiC powertransistors prototypes with a new packaging technique developed by Swerea IVF AB.It includes setting up an electrical test-bed for power and High temperature cyclingand analysis of the results. Even though test confirmed functionality after thepackaging process, (at room temperature) the performance seemed to have been reduced. This could be a result of the measurement setup and the packaging process.In higher temperature the transistors failed to operate longer than a couple ofminutes which showed the weaknesses in the design and the challenges with this typeof packaging..

The aim with the thesis is to get deeper knowledge in one of the subjects botany, livestock technology or economy. I have chosen to get deeper knowledge in how to store potatoes. How are you going to act to keep the quality on the potato during the storage, with a minimum of weight lost? My aim with this thesis is to get a view over how the potato act in storage space. The storage environment is very important in the storage space.

In this final thesis a rough description of aluminium extrusion is made, the importance of temperature of both the raw material and the extruded profile for a good profile quality. The difficulty in controlling these temperatures are discussed and attempts to increase the control are described. The attempts are basically made by controlling the furnace that is heating the raw material. This is done in a manner that the raw material reaches its final temperature shortly before it is extruded. An IR-camera at the press can be used for profile temperature measurements.

SAPA´s resource of waste heat is the basis for this thesis to investigate the possibility of energy assets in their cooling water and possible uses for it. The energy in the waste water is greater than the current need which has three uses which are (1) heating the factory, (2) converting liquid propane to propane gas and (3) local domestic heating. The average energy load that is available is 1, 7 MW and the average temperature in the cooling water is 41°C. The total energy load at dimensioning out side temperature is approximately 1,6 MW for the three current uses. The temperature is currently too low to be used directly in the existing systems so an upgrade is needed.

AbstractWith increasing population and increasing demands for comfort and thus an increase in energy demand, it is necessary to examine various energy-efficiency measures. This work deals with the ability to control the flow through the heating system to achieve the desired comfort with as little energy as possibleA heating system contains of different parts, roughly speaking, you can divide it to three main components: Heat source, Distribution and Heat emitters. All components are working together to bring heat to the building. What is examined in this report are different ways of adjusting the flow and supply temperature and how it affects comfort and energy use in a building.At today ?s date the conventional method is to use a high flow through the heating system, which affects pressure drop and cooling of the fluid.

The district heating load is seasonally dependent, with a low load during periods of high ambient temperature. Thermal energy storage (TES) has the potential to shift heating loads from winter to summer, thus reducing cost and environmental impact of District Heat production. In this study, a concept of High temperature borehole thermal energy storage (HT-BTES) together with a pellet heating plant for temperature boost, is presented and evaluated by its technical limitations, its ability to supply heat, its function within the district heating system, as well as its environmental impact and economic viability in Gothenburg, Sweden, a city with access to high quantities of waste heat.The concept has proven potentially environmentally friendly and potentially profitable if its design is balanced to achieve a good enough supply temperature from the HT-BTES. The size of the heat storage, the distance between boreholes and low borehole thermal resistance are key parameters to achieve High temperature. Profitability increases if a location with lower temperature demand, as well as risk of future shortage of supply, can be met.

This thesis examines a possible control strategy to minimize flow fluctuations in Uppsala?s district heating system. High variations in flow rate may lead to complications caused by hydraulic constraints in the district heating system. These complications, such as inadequate pressure and temperature levels, increase the risk of heat delivery failures. It is therefore important to avoid such situations both for the producer and for the customers.Typically, the forward temperature is controlled by using a rough correlation with respect to the outdoor temperature.

Glass has sophisticated front properties and are used as facades in high buildings. During cold periods, these glass facades could cause thermal discomfort, due to cold downdraught. Cold downdraught can be countered by placing heaters under glass surfaces. Nowadays technology offers highly insulating windows, which is why there is an interest to investigate the indoor climate with only underfloor heating. The research in this area is limited, and few empirical methods are available.

A district heating plant has the advantage that it can take advantage of the waste heat from industries and use of cheap fuels to produce heat. But for the long term is competitive requires that energy is also saved in district heating plants. One way to save energy in a district heating system is to increasing cooling to the return temperature. This leads to less power needed to drive the distribution pumps,  and that more energy could be extracted from the same amount of fuel by an improved flue gas condensation.In Karlskoga the return temperature into the district heating plant is high. They would therefore reduce the return temperature in order to extract more energy from the flue gases.

The aim of the present study was to evaluate the effects of large amounts of straw in the farrowing pen on thermal regulation of the newborn piglet in different weight classes. 20 sows were given 15 kg of straw in the farrowing pen 2 days prior to until 7 days after parturition. A control group of 18 sows had no straw in the pen. 6 litters from each treatment were observed. Measurements of piglet body temperature were made at 0h, 2h, 4h, 8h and 24h after parturition. At ?8h? the body temperature of the piglets in the Straw group were significantly higher (P=0,0149) than the piglets in the Control group.

Climate and environmental issues is now high on the agenda. We live in a generation that must try to solve some major environmental problems. Buildings and habitations account for approximately 40 % of Sweden's total energy today. To reduce this figure, as needed, more research in the field of energy efficiency is required.This thesis concerns the heating of buildings. The load on district heating is heavy during certain times of the day.

Aim: To examine the reaction of extreme preterm infants with regarding to body temperature and transepidermal water loss during skin-to-skin care according to Kangaroo Mother Care (KMC) during the infant?s first week of life. Method: This was a descriptive quantitatively designed study, which was a pilot study within the framework of a larger project. Nine children, with a median gestational age of 24.91 weeks, were examined by measuring body temperature (axilla and skin temperature) as well as transepidermal water loss before, during and after KMC. Results: The study showed that skin temperature tended to rise during KMC, especially for those children who were nursed with KMC for more than 60 minutes.

Climate and environmental issues is now high on the agenda. We live in a generation that must try to solve some major environmental problems. Buildings and habitations account for approximately 40 % of Sweden's total energy today. To reduce this figure, as needed, more research in the field of energy efficiency is required.This thesis concerns the heating of buildings. The load on district heating is heavy during certain times of the day.

Energy price are on the way up to a high level that will not diminish in the future make us to focus more on the sustainable development for a better solution of residential houses. Passive house or low energy housing are one of the solution to make residential more environment friendly, in same time it´s a financial security using less energy, and saving money. The last 10 years in Germany and all around Europe the concept of passive house been developed, and people aim to know more about these concept that leading the market more attractive for passive houses. A passive house is a well designed building highly insulated and air tight with mechanical ventilated system for the whole building envelope that minimizes the use of energy for heating [1].The housing company Mimer has chosen to invest in low energy consumption in every new housing project.  These future plan projects are decided to use less than 75 kwh per square meter annually in purchased energy [2].This thesis is about new constructed passive houses, and focuses on the evaluations of the temperature, and moisture condition for attic, external walls and joist.

Today, there are no regulations saying that cows must have access to some kind of shelter at pasture during the summer. In more tropical countries, it is well-known that dairy cows might suffer from heat stress when exposed to sun and High temperatures. The well-being of the cows is thereby reduced and the production may also decrease. In Sweden, no research has been done in the area and therefore it is now a clear need of improved knowledge.The purpose of this study was to investigate the importance of shade for dairy cows in Sweden. The behaviour of 30 cows was examined to see any differences between cows with access to shade and cows without access to shade.